Buy ASTM D CLASSIFICATION SYSTEM FOR NYLON INJECTION AND EXTRUSION MATERIALS (PA) from SAI Global. ASTM D Standard Classification System for Nylon Injection and Extrusion Materials (PA). standard by ASTM International, 07/01/ View all product. 暂无评价|0人阅读|0次下载 | 举报文档. D – 01A Nylon Injection and Extrusion Materials_能源/化工_工程科技_专业资料。ASTM D标准.
|Published (Last):||16 September 2012|
|PDF File Size:||5.90 Mb|
|ePub File Size:||19.96 Mb|
|Price:||Free* [*Free Regsitration Required]|
The specimens tested are 3. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Note 1 — There is no known ISO equivalent to this standard.
ASTM D – 94b Standard Classification System for Nylon Injection and Extrusion Materials (PA)
It is recommended that the material manufacturer be consulted on all call-outs against this classi? There may be other requirements necessary to identify particular characteristics important to specialized applications. Tensile strength and elongation shall be determined on Test Method D test specimens 3.
These are electrical limits applied to reinforced nylons when control of their electrical properties is required. NOTE 12—An example of a special material using this classi? L Izod impact requirements for Group 04 materials based on specimens with a The report shall consist of results of the lotacceptance inspection for the shipment and the results of the most recent periodic-check inspection.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. It is recommended that the d466 manufacturer be consulted on all call-outs against this classification system.
The electrodes shall be inserted after the specimens have been conditioned. Plastic and Ebonite ISO Military and Federal Specifications and Standards: If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
The specimen shall be of sufficient size so that two 4. Some of these compositions are also suitable for compression molding and application from solution.
Nylon 6 Supplier | Type 6/6 Nylon | Nylon Sheet
asm Start the test within 2 min after removing the specimen and wiping with a dry cloth. Packing, Packaging, and Marking All other grades are listed by requirements. General Principles ISO It is possible, by agreement between the d0466 and the seller, that materials incorporating other pigments or soluble stabilizers, or both, may prove adequate for particular applications.
The following pieces are to be used for the listed relevant test methods: Link to Active This link will always route to the current Active version of the standard. This standard d466 not purport to address all of the safety concerns, if any, associated with its use.
After the humidity conditioning speci? Some of these compositions are also suitable for compression molding and application from solution.
NOTE 11—Pigmented or colored nylons can differ signi? A number in parentheses indicates the year of last reapproval. J Carbon black content and absorbance must be 1. A superscript epsilon e indicates an editorial change since the last revision or reapproval. D — 01a Standard Classi?
Link to Active This link will always route to the current Active version of the standard. Seven laboratories, including 3 U. Material data for inje Table PA is used to specify the group of nylon and Table A or B is used to specify property requirements.
Historical Version s – view previous versions of standard. It is the responsibility of the user of this standard to establish appropriate safety and d40666 practices and determine the applicability of regulatory limitations prior to use. Flexural modulus shall be determined on Test Methods D test specimens 6.
Industrial & Engineering Plastics
These may be speci? Thus, a letter designation G for glass reinforced and 35 for percent or reinforcement, G35, speci? E Tensile strength and elongation shall be determined on Test Method D test specimens 3.